Clik here to view.
Vector CrossProduct bug?
@clement wrote: Hi @DavidRutten, i am facing below using GH in RH6: grafik.png1548x596 153 KB Is there maybe something wrong using VectorCrossProduct ? _ c. Posts: 9 Participants: 3 Read full topic
View ArticleClik here to view.
Subdivide Surface by Repeating Module
@kyanovska wrote: Hello, I am trying to break up a surface into smaller planar pieces, perhaps using one repeating module to rebuild entire surface, or a few modules that come together to build the...
View ArticleLoft failing following polyline offset weave
@maglar2 wrote: Hi all, Yet another silly n00b question: trying to thicken a voronoi mesh projected onto a trimmed and sinuous surface, and I can’t make this loft work. The attached snippet is part of...
View ArticleClik here to view.
Finding points on the curves
@John_Johnson wrote: Hi, how can I find the points on these curves as shown on the attached image? Capture.JPG1658x838 723 KB Building-MP_re.gh (74.7 KB) Building.3dm (979.0 KB) Posts: 3 Participants:...
View ArticleClik here to view.
Troubleshooting_Joining n surfaces with a very small surface next to it
@huskenazy wrote: Hi all, I’m strugglin with this. I have some surfaces, and i separate from them the surfaces with the edge smaller than x value. Then i want to join this small surface with the...
View ArticleClik here to view.
Galapagos bug?
@andy.vanmater wrote: Galapagos won’t use the maximum of my sliders if they are integers. Not sure why… image.png713x602 133 KB Posts: 2 Participants: 2 Read full topic
View ArticleKaramba - structral analysis doesn't seem right
@jamie.2211 wrote: Dear all I’m new to Grasshopper and Karamba. I have created a twisted bridge design in Grasshopper and wanted to do a structural analysis to find the displacement. However, the...
View ArticleClosest points with same distance issue
@flokart wrote: Hi all, i tried to get the closest points and all of them have the same distance but different locations. Unfortunatly the result with closest points give sometimes the same point two...
View ArticleClik here to view.
Split curves
@davidsmavrov wrote: I have crazy problem spliting lines or curves. I need to split multiple lines and curves at their intersection points. I need a solution which works for variety of angles between...
View ArticleClik here to view.
Divide/Trim/Redraw segment of a curve
@javiergonzalezcastil wrote: Hello, I have an ellipse with 2 points in the curve. How could I trim the curve between this 2 points? Untitled-1.jpg2480x1461 307 KB Posts: 4 Participants: 3 Read full...
View ArticleTORO plugin for grasshoppe in rhino 5
@javiergonzalezcastil wrote: Someone knows if there is a plugin of TORO available in grasshopper (rhino 5) ??? Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Object inditification
@davidsmavrov wrote: Anybody has an idea how to do the following: Lets say we have a collection of lines/curves. They are connected to other lines in our selection, but they form different “clusters”....
View ArticleClik here to view.
Seat hinge close open simulation
@Czort wrote: Hello Everyone, I would like to achive this final result as on photo attached. I would like to use rotate button to control movement of the hinge. In attached gh file is all i did so...
View ArticleClik here to view.
How can I group points by their Z value and draw a nurbs curve between them?
@TheCyclist wrote: I have 50 points as seen in the screen capture. There are five different Z values between all the points, 10 points at each Z value. I trying to figure out a way to group the points...
View ArticleRhino 6 Grasshopper crashing
@henry1 wrote: Hi, I just installed Rhino 6 and opened up a project I’ve been working on. I’m getting frequent and unexpected crashes. By crash I mean I’m getting the Rhino 6 stopped working and...
View ArticleClik here to view.
Ruled Nest pattern
@PZeth wrote: Hello everyone! This is my first experience in building something within Grasshopper and I’m trying to play and set my first definition. Here is it what i’m trying to achieve:...
View ArticleWB Yak Installation
@brobes05 wrote: Hello, This is probably a simple issue, but I cannot figure out how to install WB with the YAK installer in the new GH. I open the file and it simple gives me a list of missing...
View ArticleGeometry pipeline including geometry within blocks
@benjamin wrote: Any way of getting pipelines to work with geometry within blocks? Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Need help identifying this icons
@wespor wrote: Still new with grasshopper, I’m working on a voroni project and this seems like a good starting spot for what I’d like to make, I’d like to understand the script but I can’t recognize...
View ArticleClik here to view.
Shrink and Divide patch surface?
@cokerone1214 wrote: Hello ! I am trying to create a framework of a parametric surface which has been created with patch command. However when i divide the surface it devides all the untrimmed...
View Article