Clik here to view.
How to show curves and points in rendered and/or Arctic mode
@Holo wrote: As the title says, how do I show Grasshopper generated points and curves in renderd and/or arctic mode? I get them to show in Shaded: But in arctic I only get the surface to show as I...
View ArticleClik here to view.
Domain Slider
@c.gressel wrote: Hey! Some time ago i found a picture in the internet of a slider where you can input a domain and then slide between these min an max values. but im not sure if this component really...
View ArticleClik here to view.
Domain Slider
@c.gressel wrote: Hey! Some time ago i found a picture in the internet of a slider where you can input a domain and then slide between these min an max values. but im not sure if this component really...
View ArticleClik here to view.
Unexpected result using pulling points
@Schell wrote: Could any of you help me what could be the reason of the unexpected result : ? P-02.jpg866x557 105 KB P-03.jpg1909x1040 210 KB The 6th 3D edge-segment is not pulling the points of the...
View ArticleClik here to view.
Easiest way to simulate sheet metal under tension (pic inside)
@zoster wrote: Hey all, I want to simulate the bending of a square piece of sheet metal as in the attached pic. How wold You advise me to go about it? (I’m not necessarily interested in the forces)...
View ArticleClik here to view.
Import obj directly into Grasshopper
@prcthms wrote: hi all, I used to use the LocalCode import component (see image) to reference .obj files directly into Grasshopper, but it doesn’t seem to be doing it anymore. Is there another way to...
View ArticleCan't get any bigger fillets than 20-30mm? They don't get anywhere near the...
@Mikael_Liback wrote: Don’t know what’s wrong here. I googled a bit and saw some others having similar issues. But in their case it was cause the fillet would go past the middle of the lines. In my...
View ArticleClik here to view.
Sweep2 Solution found
@Birk_Binnard wrote: This topic is a lengthy discussion about a problem I encountered with the Sweep2 component in GH Ver. 1.0.004. The strange result I got using the same basic GH code I used in...
View ArticleClik here to view.
HELP A NEWBIE! :) Problem with attractor point
@pam.alvaguer wrote: Hi! I am having a problem working with attractors and a defined geometry, i want to scale the shell shaped geometry that you can see in their own center and this scale depending...
View ArticleClik here to view.
MESH DIFFERENCE not working
@ngjurchin wrote: I tried using difference option, but it’s not working on all geometries within Grasshopper. Does anyone had the same problem? I am sending the file where you can see at the end when...
View ArticleMultiple point attractors
@Stratosfear wrote: I’ve given my best try to get this to work with multiple attractors. I can set multiple points but only one will work. 1.3.2.1_attractor definition.gh (8.3 KB) Posts: 2...
View ArticleLooking for training pdf for grasshopper
@Joe4 wrote: I have been using Rhino5 quite a bit, but nowhere near where I’d like to be. But I have found the Level 1 training pdf and models extraordinarily helpful. Now I am evaluating Rhino6 and...
View ArticleLargest Brep in Brep
@panacer wrote: Hi i have a problem with a very simple logic so i didnt attach any files because they wont be much use. I have created a simple voronoi in a cube, which results in non orthogonal...
View ArticleAttempt to give K1 an K2-style "On" input; only work outside cluster
@gankeyu wrote: I’m trying to give K1 solver an ‘On’ input. My attempt was successful outside a cluster. But when I move solver and my component into a cluster, it doesn’t work. So I’m looking for...
View ArticleDoes kangaroo work with trees?
@zoster wrote: Hey all, Short question about Kangaroo 2: can the solver output more than one result by using a tree structured input for the goals? (having say 10 branches with 10 separate sets of...
View ArticleClik here to view.
Flipping GH Planes forever? What is going on and how to fix it?
@RIL wrote: Many of us has struggled with them, and it just keeps haunting us - Planes which doesn’t really know which way to orient itself. But wasn’t it exactly this that Quaternions was good for,...
View ArticleClik here to view.
GH import3DM > missing full path option
@Asaf_Yaacobi wrote: Screenshot_181.png1764x650 81.6 KB maybe in the upcoming update? thnx {same issue with HUMAN plugin (read 3dm file component) } Posts: 1 Participants: 1 Read full topic
View ArticleGrasshopper compatibility Rhino5 v Rhino6
@merijndeleur wrote: Hi all, I was wondering if the defenitions made in the latest grasshopper version for Rhino5 are compatible with the new Rhino6 version. I’m on the point of upgrading to Rhino6,...
View ArticleCurve cutting interior grid pattern as a clean line
@aideenmod wrote: I’m working with paving patterns and I have made a grid of pavers and want to cut them as a clean line. The script that I have created cuts the pattern but not the individual stones....
View ArticleCompare Volume Lists
@panacer wrote: Hi my objective is to simplify a voronoi cell into orthogonal shapes and i have divided each voronoi cell’s bounding box into 4x4x4 boxes, and subsequently, solid intersection these 64...
View Article