Clik here to view.
Backward incompatibility Grasshopper components
@Bas_Goris wrote: Hi, I have worked on a grasshopper file in Rhino 6, which should be available in Rhino 5 for other users. Is there a way to save my file as an old version? Or is there a way to find...
View ArticleClik here to view.
Missing Components -Rhino 6 Grasshopper
@austin1 wrote: I downloaded Rhino 6 evaluation and no longer see the new fillet edge components in the surface tab after a computer restart. I can access them on my laptop with the same license but...
View ArticleClik here to view.
Distance between curves
@StructureEmma wrote: Hi, I am trying something in grasshopper, but my knowledge doesn’t go so far to know if it’s right what I am doing till now. I have read some posts but doesn’t find exactly what...
View ArticleClik here to view.
Surface Morph on specific list surfaces
@cokerone1214 wrote: hello! I have a curved wall divided on 23 segments and i am trying to create a list of the segments i want to adapt my geometry but when i connect my list to the surface option of...
View ArticleClik here to view.
Color analysis
@clau.domi wrote: I would like to know if there is a way to use a Grasshopper tool to plot a color scheme like the figure below in curves or surfaces. image.jpg780x542 80.7 KB Posts: 2 Participants: 2...
View ArticleSin curve and alter the height of one single curve?
@brianda.guevara wrote: sin curve and alter the height of one single curve? thanks. Posts: 2 Participants: 2 Read full topic
View ArticleHow to create a sine curve and alter the height?
@brianda.guevara wrote: how to create a sine curve and alter the height? Posts: 3 Participants: 3 Read full topic
View ArticleClik here to view.
How do i make this type of parameterization in grasshopper?
@micahrdinero wrote: hi is there anybody who can help me how to make this parameterization in grasshopper? and also extrude framings along joints and making curved glass on the face. the coordinates...
View ArticleClik here to view.
How to do with this gradient
@823165569 wrote: how to do with this gradient，I am very puzzling，Thank you 33.JPG610x828 72.9 KB Posts: 5 Participants: 2 Read full topic
View ArticleClik here to view.
Offset Curve On Surface
@ra_mull wrote: In GH I’m offsetting the curve and getting rounded corners. I know this is because when I join a line-like curve and a planar curve (with degree other than 1) all my lines change...
View ArticleTwo point curve with restricted length how to?
@juanstefani wrote: I have two points and I want to connect them with a bezier curve. The curve must have a certain length. I need these for pattern making. So I need to be a certain length to match...
View ArticleUnroll Brep apparently broken in V6
@osuire wrote: I used to get good Brep unrolls in V5 with the Fabtools “Unroll” component. Now it fails to properly unroll all the faces in V6. I tried the “Unroll Brep” component from “Wombat”, and...
View ArticleC# - assigning color to points according to distances moved?
@nesfut wrote: i’m trying to assign colors to points moved inside a c# component in grasshopper. i would like to assign different color depending on the distance each point moved. (inside the same c#...
View ArticleGrasshopper slider animation, Export Sequence (to be used for rendering)
@FordEarl wrote: Hello Scripters, Can anyone point me in the right direction (a previous thread or solution) for a script, that allows me to export geometry (surface or solid) from Grasshopper, to...
View ArticleClik here to view.
Component upgrade nasty little trap
@osuire wrote: I had definitions definition that used to work perfectly in V5 and produced garbage in V6, not understanding what was causing this. After some research, I found out that the automatic...
View ArticleClik here to view.
Duplicate a rotated box on point
@samluong89 wrote: Hi there! I can’t seem to figure out the sequence of this script so that each step of the LINEAR ARRAYED box is 4.6m. Is there a way to combine both a Normal direction/vector...
View ArticleClik here to view.
Is it the alignment section of the angle when I do pushing out along a curve...
@Momiji.Satomura wrote: Please tell me the section about laying upon of the sectional angle when I do pushing out along a curve 0314_SectionBeam_GH_Q1.jpg1844x728 316 KB This program pushes 'H form...
View Article"1. Solution exception:WindowsError"
@Redjester wrote: I’m trying to get a definition to work called “ShortestWalkTaperedCocoonTetgenMeshBunny,” but the Python component is red and it is listed as the above exception. Any work around to...
View ArticleClik here to view.
What is the name of this component?
@arelyguevarac wrote: Posts: 7 Participants: 5 Read full topic
View ArticleClik here to view.
Stripe Pattern
@FordEarl wrote: Hey GH Community, I am looking for some help in creating a stripe pattern inside any given perimeter (or multiple) curve(s). I am sure there are better and more sophisticated ways to...
View Article